- 您现在的位置：买卖IC网 > Sheet目录1216 > FR3-32M (TechTools)EMULATOR MEMORY FLEXROM 3
Connect the Download Cable
Select an unused PRINTER port on your PC. Remove any “dongles”, security keys, printer switch boxes
or extension cables from the port. Plug the supplied download cable directly into the selected printer port.
Plug the other end of the cable into FlexROM III’s “IN” port.
PLUGGING FlexROM III INTO A SERIAL PORT or
an ETHERNET CABLE COULD DAMAGE THE
EMULATOR!
Connect Daisy-chain Cables
Multiple units are daisy-chained by connecting the “OUT” connector from one unit to the “IN” connector of
the next unit. Additional units are added in the same manner. Use the supplied 12” daisy-chain cable to
interconnect the units.
When daisy-chained together, the emulators automatically determine their position in the chain, making it
unnecessary to configure their addresses. However, it is important that you understand how their addresses
are determined.
The LAST EMULATOR in the chain (the one without a cable plugged into its “OUT” connector) is
always emulator #1 . The next emulator in the chain is #2 and so forth. The emulator closest to the PC
will always be the highest numbered emulator.
Run self-test
Running self-test immediately after installation gives you a solid baseline and helps you to find and correct
any errors early on. Self-test will verify proper installation of all drivers, proper operation of the parallel
port and all FlexROM III functions except the target interface buffers.
You will find 16 and 32bit console mode programs in directories below your install directory. The 16bit
self test is included in case you plan to use the 16bit loader on a DOS machine. The 32bit self-test should
be used if you are planning to use the Windows Quickloader or the 32bit console mode loader. We
recommend using the 32bit self-test if you are running under Windows 95 or above. You can also invoke
the 32 bit self-test program from within Quickloader.
If you are using multiple FlexROM IIIs, we recommend that you test them collectively to ensure reliable
operation in the final configuration.
Type “RTTEST32” to run a full speed test over printer port 0x378. You can change the printer port by
using a /P parameter. For example, if your emulator is connected to a printer port at 0x3bc, you would
enter “RTTEST32 /P3BC”. The most common printer port addresses (in order of popularity) are 378,
278 and 3bc. Type “RTTEST32 ?” to see all command line options.
FlexROM III User’s Manual
10
Copyright ? 2001, TechTools
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
FS-9062
JTAG_BOOSTER FOR ANALOG DEVICES
FS-977
JTAG-BOOSTER FOR 386EX 3.3V
FS1-R26-2000
CONN RECEPT MINI SAS 26POS SMD
FS1-R26-2001
CONN RECPT SAS MINI 26POS SMT
FS1-S01-146E1
CONN SNGL M-SAS CAGE KEY 4,6 P1
FS1-S02-1D66E1
CONN MINI SAS CAGE 1X2 R/A SMT
FS1-SF1-14E1
CONN SNGL M-SAS CAGE KEY 4 P0
FS1-SF2-14E1
CONN DUAL M-SAS CAGE KEY 4 P0
相关代理商/技术参数
FR34
制造商:FCI 制造商全称:First Components International 功能描述:3.0 Amp FAST RECOVERY PLASTIC RECTIFIERS
FR3492-D
制造商:BACO Controls Inc 功能描述:
FR3492-D1
制造商:BACO Controls Inc 功能描述:
FR3492-D2
制造商:BACO Controls Inc 功能描述:
FR3492-D3
制造商:BACO Controls Inc 功能描述:
FR3492-D5
制造商:BACO Controls Inc 功能描述:
FR3492-D6
制造商:BACO Controls Inc 功能描述:
FR3492-D7
制造商:BACO Controls Inc 功能描述: